GTU · First Year Common · Semesters 1 and 2
GTU 3110013 Engineering Graphics & Design (EGD) Old Question Papers PDF
Official Gujarat Technological University (GTU) old question papers PDF (Regular & Remedial) and step-by-step solved questions for Engineering Graphics & Design (EGD) across 2023 – 2026 examinations.
26 questions GTU asked more than onceAsked in all 7 papers: A line PQ is 120 mm long. It is inclined at 45° to the HP and 30° to the VP. The end P is 15 mm above HP and 25 mm in front of VP. Assuming the end Q in the first quadrant, draw the projections of the line PQ.See listExam papers
Most repeated questions
26 questions GTU set in two or more of 7 papers, most repeated first. Tap a year to open that paper at the question.
A line PQ is 120 mm long. It is inclined at 45° to the HP and 30° to the VP. The end P is 15 mm above HP and 25 mm in front of VP. Assuming the end Q in the first quadrant, draw the projections of the line PQ.
Summer 2026 Q2c OR Summer 2026 Q3c Summer 2026 Q3a OR Summer 2026 Q3c OR Winter 2025 Q2c Winter 2025 Q2c OR Summer 2025 Q2c Summer 2025 Q3b Summer 2025 Q3a OR Summer 2025 Q3c OR Winter 2024 Q3c Summer 2024 Q3b Summer 2024 Q3c Winter 2023 Q3b OR Winter 2023 Q3c OR Summer 2023 Q3a Summer 2023 Q3a OR
A semicircular plate of 90mm diameter has its straight edge in the HP and inclined at 45⁰ to the VP. The surface of the plate makes an angle of 30⁰ with the HP. Draw its projections.
Summer 2026 Q2c Summer 2026 Q4c Summer 2026 Q4b OR Winter 2025 Q3c Winter 2025 Q3c OR Summer 2025 Q4b Summer 2025 Q4b OR Winter 2024 Q3a Winter 2024 Q3b Winter 2024 Q3b OR Winter 2024 Q3c OR Summer 2024 Q4c Summer 2024 Q4b OR Winter 2023 Q3b Winter 2023 Q3c Winter 2023 Q4c OR Summer 2023 Q3b Summer 2023 Q3c Summer 2023 Q3b OR Summer 2023 Q3c OR
Draw all three orthographic views of the object given below using third angle projection.
Summer 2026 Q5c Winter 2025 Q5c Summer 2025 Q5b OR Winter 2024 Q5b Summer 2024 Q5b Winter 2023 Q5b Summer 2023 Q4c OR Summer 2023 Q5c OR
Draw a diagonal scale of R.F, 1:12 showing yard, feet and inch and long enough to measure up to 3 yards. Show a distance of 1 yard 2 feet and 3 inch on it.
Summer 2026 Q2b Winter 2025 Q1a Summer 2025 Q1b Winter 2024 Q1c Summer 2024 Q1b Winter 2023 Q1b Summer 2023 Q1b
Draw the projections of the points A and B on the same X-Y line. (a) Point ‘A’ is in second quadrant and 45 mm from H.P and 25 mm from VP. (b) Point ‘B’ is in Fourth quadrant and 35 mm from H.P and 55 mm from VP.
Summer 2026 Q1b Winter 2025 Q2a Summer 2025 Q2b Winter 2024 Q3a OR Summer 2024 Q3a Winter 2023 Q4b Summer 2023 Q2a
Draw isometric view of the frustum of cone whose height is 60 mm, Base radius is 40mm and top radius is 25mm.
Summer 2026 Q5b Summer 2026 Q5c OR Winter 2025 Q5c OR Summer 2025 Q5b Winter 2024 Q5c OR Summer 2024 Q5b OR Winter 2023 Q5b OR Summer 2023 Q5c
A cone of 40 mm diameter and 60mm length is resting on HP. Its axis is parallel to H.P and V.P both. Draw its projection.
Summer 2026 Q4a Summer 2026 Q4b Summer 2026 Q4c OR Winter 2025 Q3b Summer 2025 Q4c OR Winter 2024 Q4c Winter 2024 Q4c OR Summer 2024 Q4c OR Summer 2023 Q4b
A cylinder with 50 mm base diameter and 80 mm height is cut by a sectional plane from the center of axis such that the cross-section is an ellipse with major axis 70 mm. draw the projection of cylinder and find angle of sectional plane with HP, if the sectional plane is perpendicular to VP.
Summer 2026 Q4a OR Winter 2025 Q4c Summer 2025 Q4c Summer 2025 Q4a OR Winter 2024 Q4b Winter 2023 Q4c Winter 2023 Q4b OR Summer 2023 Q4c Summer 2023 Q4b OR
The major and minor Axis of an ellipse is 120 mm and 80 mm respectively. Draw upper half ellipse by concentric circle method and lower half by arc of circle method. Also Find distance between its foci points.
Summer 2026 Q1c Winter 2025 Q1c Summer 2025 Q1c Winter 2024 Q2c OR Winter 2023 Q2c OR
Draw an involute of a square having 30 mm side. Also draw normal and tangent at any suitable point on it.
Summer 2026 Q3b Summer 2025 Q3b OR Winter 2024 Q2c Summer 2024 Q1c Summer 2023 Q1c
Show 16 more repeated questionsHide the 16 more
What are the advantages and disadvantages of using AUTOCAD?
Winter 2025 Q4b OR Summer 2025 Q5a OR Winter 2024 Q5b OR Winter 2023 Q4a OR Winter 2023 Q5a Summer 2023 Q5a
An insect is moving on a stick AB 100mm long from point A to B in T sec. the stick also revolves along its midpoint c and completes one revolution in the T sec. Draw the locus of the insect.
Summer 2026 Q3b OR Winter 2025 Q1b Summer 2024 Q2c Summer 2023 Q2c OR
Explain different types of lines with their illustrations and applications.
Winter 2025 Q4b Winter 2024 Q1b Winter 2023 Q2b Summer 2023 Q1a
Explain about development of lateral surface of various types of solids used in engineering drawing.
Summer 2026 Q1a Winter 2025 Q4c OR Summer 2025 Q4a Summer 2024 Q2b
Explain first angle and third angle projection system with their symbols.
Winter 2025 Q4a OR Summer 2025 Q1a Summer 2024 Q4a Summer 2023 Q4a OR
Explain the following AUTOCAD commands
Differentiate between aligned system and unidirectional system of dimensioning using sketches.
Define ellipse, parabola and hyperbola based on eccentricity ratio.
Winter 2025 Q4a Winter 2024 Q2a Winter 2023 Q2a Winter 2023 Q4a
A thin circular disc of 50 mm diameter is allowed to roll without slipping from upper edge of sloping board which is inclined at 15° with the horizontal plane. Draw the curve traced by the point on the circumference of the disc. Consider the point is at contact surface of disc and sloping board initially.
Draw a parabola by rectangle method, given its base as 90 mm and the height of axis is 75 mm.
OBA is a simple slider crank chain. OB is a crank of 30 mm length. BA is a connecting rod of 90 mm length. Slider A is sliding on a straight path passing through point O. Draw the locus of the mid-point of the connecting rod AB for one complete revolution of the crank OB.
Draw isometric circle on the three sides of cube of 60 mm dimension using four centre method.
Classify solids based on their geometric properties.
Draw isometric scale showing 100 mm normal scale.
Differentiate between prism and pyramid.
Explain the importance of scale in engineering drawing. Explain about different types of scales and their use.
Which branches take this subject
GTU's syllabus lists 3110013 for 45 branches. One set of papers serves all of them.
Semester 1: 45 branches
Aeronautical Engineering, Artificial Intelligence and Data Science, Artificial Intelligence and Machine Learning, Automobile Engineering, Bio-Technology, Biomedical Engineering, Chemical Engineering, Chemical Engineering (Green Technology & Sustainability Engineering), Chemical Technology, Civil & Infrastructure Engineering, Civil Engineering, Computer Engineering, Computer Science & Design, Computer Science & Engineering, Computer Science & Engineering (Artificial Intelligence and Machine Learning), Computer Science & Engineering (Cyber Security), Computer Science & Engineering (Data Science), Computer Science & Engineering (Internet of Things and Cyber Security Including Block Chain Technology), Electrical Engineering, Electronics & Communication Engineering, Electronics & Instrumentation Engineering, Electronics and Communication (Communication System Engineering), Electronics Engineering, Environmental Engineering, Environmental Science & Technology, Food Engineering & Technology, Food Processing Technology, Industrial Engineering, Information & Communication Technology, Information Technology, Instrumentation & Control Engineering, Manufacturing Engineering, Mechanical Engineering, Mechatronics Engineering, Metallurgy Engineering, Mining Engineering, Nano Technology, Plastic Technology, Plastics Engineering, Power Electronics, Production Engineering, Robotics and Automation, Rubber Technology, Smart & Sustainable Energy, Textile Technology
Other Semester 1 subjects
Common questions
Are these GTU 3110013 Engineering Graphics & Design papers valid for both Regular and Remedial exams?
Yes. Gujarat Technological University (GTU) follows the same 70-mark syllabus, exam blueprint, and 23-mark passing cutoff for both Regular and Remedial (ATKT/backlog) examinations. All 7 past exam sessions (2023 – 2026) serve as comprehensive preparation for either attempt.
How can I download GTU 3110013 Engineering Graphics & Design old question papers PDF?
You can download official GTU 3110013 original question paper PDFs directly from the table above with 1 click and zero deceptive ads or wait timers. Every paper also includes interactive online questions with AI study prompts.
What is the passing mark for GTU Engineering Graphics & Design (3110013)?
The external theory exam carries 70 marks. The minimum passing cutoff is 23 marks (33%). Exam duration is 2.5 hours.
What is the GTU exam pattern for 3110013?
The examination contains 5 main questions of 14 marks each, totaling 70 marks. Questions 2 through 5 provide internal OR choices, typically split into 3-mark, 4-mark, and 7-mark questions.